| @@ -0,0 +1,82 @@ | |||
| 1 | + | # P65: memory map and I/O registers | |
| 2 | + | ||
| 3 | + | The 65C02 sees 64 KB. All of it lives in one array in the Pico (`cpu_memory[]`); | |
| 4 | + | there is no address decoder in hardware, so the map below is decided purely by | |
| 5 | + | the firmware (core 1 bus loop, `src/65c02.c`, `include/mapper.h`). | |
| 6 | + | Names come from `include/mapper.h`, `emulator/memmap.py` and the equates at the | |
| 7 | + | top of `asm_examples/testrom1.a65` - keep the three in sync. | |
| 8 | + | ||
| 9 | + | ## 1. Map | |
| 10 | + | ||
| 11 | + | | Address | What | | |
| 12 | + | |----------------|------| | |
| 13 | + | | `$0000-$7FFF` | RAM, 32 KB (zero page, stack, BASIC, programs) | | |
| 14 | + | | `$8000-$80FF` | I/O page (registers below; unused offsets read the stored byte, writes ignored) | | |
| 15 | + | | `$8100-$FFFF` | ROM image (BASIC, 32512 B), writes ignored - **or RAM when ROMCTL bit 0 = 1** (section 3) | | |
| 16 | + | ||
| 17 | + | ## 2. Registers (offset from `$8000`) | |
| 18 | + | ||
| 19 | + | | Addr | Name | Access | Meaning | | |
| 20 | + | |---------|---------|--------|---------| | |
| 21 | + | | `$8000` | LEDS | W: bits 0-2 = LED0..2 (1 = on); R: `$F8` or leds | the three LEDs | | |
| 22 | + | | `$8001` | KEY | R: bit 7 = key waiting, bits 0-6 = ASCII; W: any value acknowledges | keyboard (8-char queue in the Pico) | | |
| 23 | + | | `$8002` | VDATA | R/W | TMS9918 data port, VRAM address auto-increments | | |
| 24 | + | | `$8003` | VCTRL | W: address / register; R: status | TMS9918 control / status. Status read clears flags and releases /IRQ; bit 7 = 60 Hz frame flag. See `VSYNC.md` | | |
| 25 | + | | `$8004` | ROMCTL | W: bit 0; R: bit 0, bit 7 | ROM on/off, see section 3 | | |
| 26 | + | | `$8010-$802F` | STORAGE | mailbox | flash file system, see `STORAGE.md` | | |
| 27 | + | | other | | | unused | | |
| 28 | + | ||
| 29 | + | ## 3. ROMCTL (`$8004`): switching the ROM off | |
| 30 | + | ||
| 31 | + | Gives the program 32 KB more RAM at `$8100-$FFFF`. | |
| 32 | + | ||
| 33 | + | | Bit | Write | Read | | |
| 34 | + | |-----|-------|------| | |
| 35 | + | | 0 | `1` = ROM off (area above the I/O page is RAM), `0` = ROM on (image restored) | current state (1 = ROM off) | | |
| 36 | + | | 7 | - | **busy**: the ROM image is being copied back, do not run ROM code yet | | |
| 37 | + | ||
| 38 | + | * Switching off changes nothing in memory: the ROM image stays at `$8100-$FFFF` | |
| 39 | + | until the program overwrites it, so ROM routines can still be called as long as | |
| 40 | + | their bytes are intact. | |
| 41 | + | * Switching on makes core 0 copy the 32 KB image back (about 0.3 ms, estimate, | |
| 42 | + | not measured). Poll bit 7 until it is clear. | |
| 43 | + | * `$8000-$80FF` stays I/O in both modes, so RAM is split: `$0000-$7FFF` and | |
| 44 | + | `$8100-$FFFF`. | |
| 45 | + | * With the ROM off, `$FFFA-$FFFF` (NMI / RESET / IRQ vectors) are RAM too: | |
| 46 | + | **the program must write its own vectors**, and an IRQ before that jumps | |
| 47 | + | into garbage. Keep interrupts disabled (`SEI`) across the switch. | |
| 48 | + | * Storage `LOAD` / `BLOAD` / `BRUN` may write above `$8100` while the ROM is off | |
| 49 | + | (otherwise such a load is refused with "address"). A file must not cross the | |
| 50 | + | I/O page. | |
| 51 | + | * Not restored by: Ctrl+= and the CPU reset done by `main.c` (only at power up). | |
| 52 | + | If a program with the ROM off hangs, power-cycle the Pico. | |
| 53 | + | ||
| 54 | + | Exit to BASIC from a program that switched the ROM off: | |
| 55 | + | ||
| 56 | + | ```asm | |
| 57 | + | sei | |
| 58 | + | stz $8004 ; ROM on | |
| 59 | + | wait: lda $8004 | |
| 60 | + | bmi wait ; bit 7 = still copying | |
| 61 | + | jmp ($FFFC) ; cold start; or jump to the BASIC warm start | |
| 62 | + | ``` | |
| 63 | + | ||
| 64 | + | Switching off: | |
| 65 | + | ||
| 66 | + | ```asm | |
| 67 | + | sei | |
| 68 | + | lda #1 | |
| 69 | + | sta $8004 ; ROM off | |
| 70 | + | ; ... write your vectors at $FFFA-$FFFF, IRQ handler, etc. ... | |
| 71 | + | cli ; only if your IRQ vector is set up | |
| 72 | + | ``` | |
| 73 | + | ||
| 74 | + | Status: emulator tested (`tests/test_romctl.py`); firmware builds, **not tested on | |
| 75 | + | the board** at the time of writing. | |
| 76 | + | ||
| 77 | + | ## 4. Where this is implemented | |
| 78 | + | ||
| 79 | + | * Firmware: `include/mapper.h` (map, `rom_ram`), `src/mapper.c` (`romctl_write`, | |
| 80 | + | `mapper_rom_poll`), `src/65c02.c` (write path), `src/video.c` (calls the poll). | |
| 81 | + | * Emulator: `emulator/memmap.py`, `emulator/machine.py` (`_romctl_write`, | |
| 82 | + | `_update_rom`), `emulator/cpu65c02.py`. | |
zdebel / MEMORY_MAP.md
Last active 1 day ago
revised this gist 1 day ago
·
6d6989a
1 file changed, 82 insertions